RV Pre-Trip Inspection Checklist: What to Check Before Towing

RV pre-trip inspection checklist before towing a travel trailer

This post may contain affiliate links. If you make a purchase through one of these links, I may earn a small commission at no additional cost to you. I only recommend tools and services that can make RV travel easier to plan.


Table of Contents


A complete RV pre-trip inspection can catch loose connections, forgotten hookups, open compartments, tire problems, and unsecured cargo before they become roadside emergencies.

The inspection does not need to be complicated, but it should follow the same order every time. Begin inside the RV, disconnect and secure the campsite equipment, inspect the exterior, verify the hitch and brakes, and finish with one last walk around the entire rig.

This checklist is designed primarily for towable RVs. Motorhome owners can use many of the same steps while adding the chassis, engine, and towed-vehicle procedures required by their manufacturers.


Quick Answer: What Should You Check Before Towing an RV?

Before towing, check the RV’s tires and wheels, hitch or fifth-wheel connection, safety chains, breakaway cable, electrical plug, trailer brakes, exterior lights, propane system, doors, windows, awning, slides, steps, stabilizers, cargo, and fluid levels.

Make sure every campsite connection has been removed, including the shore-power cord, water hose, sewer hose, cable, and leveling equipment. Test the brake lights and turn signals with another person whenever possible.

Finish with a slow walk around the entire combination. Look underneath the RV, above it, and along both sides before pulling away.

WTT Tip: Follow the same inspection order every time. A repeatable routine makes it easier to notice when something is missing or out of place.


What Is an RV Pre-Trip Inspection?

An RV pre-trip inspection is a systematic check completed before moving a motorhome or towing a trailer. Its purpose is to confirm that the RV is road-ready, properly connected, and safe to move.

It is different from seasonal maintenance or a professional inspection. A pre-trip check will not replace wheel-bearing service, brake maintenance, roof inspections, appliance service, or repairs recommended by the RV, chassis, tire, axle, or hitch manufacturer.

The checklist also cannot determine whether the loaded combination remains within every applicable weight rating. Those calculations should be completed separately using actual loaded weights.

Use the manuals for your specific RV, tow vehicle, hitch, brake controller, tires, and installed equipment as the final authority. Procedures can differ between travel trailers, fifth wheels, motorhomes, and rental RVs.


Complete Part of the Inspection Before Departure Day

Some problems are easier to correct the night before travel. Waiting until checkout time can create pressure to rush or ignore an issue.

Before departure morning:

  • Review the route, fuel stops, weather, and campground checkout time.
  • Confirm that the tow vehicle and RV do not have unresolved warning lights or known mechanical problems.
  • Check for applicable vehicle, tire, or RV equipment recalls through the National Highway Traffic Safety Administration.
  • Secure heavy cargo and balance the RV according to its loading instructions.
  • Charge phones, navigation devices, tire-monitoring equipment, and emergency communication devices.
  • Confirm that required keys, registration, insurance information, roadside-assistance details, and campground information are accessible.
  • Fill the tow vehicle or motorhome when it is easier to reach the pumps without maneuvering through a crowded station.

Use How to Find RV-Friendly Fuel Stops When Towing to select a preferred fuel stop and a backup before leaving.


RV Pre-Trip Inspection Checklist

Checking travel trailer tires during an RV pre-trip inspection

1. Secure the Inside of the RV

Begin inside so you do not have to reopen the RV after completing the exterior inspection.

Latch cabinets, drawers, shower doors, refrigerator doors, and interior sliding doors. Lower or secure loose televisions, countertop appliances, tables, and other items that could move during a turn or sudden stop.

Place heavy items low and prevent cargo from shifting. Never assume an item is safe simply because it remained in place during a previous trip.

Check that:

  • People and pets are accounted for.
  • Loose objects are stored.
  • Roof vents and windows are set for travel.
  • Interior doors and room dividers are secured.
  • The refrigerator is latched.
  • Water pumps and appliances are set according to their manufacturers’ travel instructions.
  • Items cannot fall into a slide mechanism.
  • Travel locks and retaining bars are installed where required.

Walk through every room before closing and locking the entry door.

2. Disconnect Every Campsite Connection

Disconnect and store all external equipment before moving the RV.

This may include:

  • Shore-power cord and electrical adapters
  • Surge protector or electrical management system
  • Fresh-water hose and pressure regulator
  • Sewer hose and fittings
  • Black-tank flush hose
  • Cable television or internet connection
  • Portable solar equipment
  • Generator connections
  • Outdoor rugs, furniture, grills, and pet equipment

Close the termination valves, replace the sewer cap, and secure the utility compartment.

Check the ground around and underneath the RV. Small items such as leveling blocks, wheel chocks, hose elbows, pressure regulators, and electrical adapters are easy to leave behind.

3. Retract Slides, Awnings, Steps, and Stabilizers

Fully retract all slide rooms and confirm that they have seated correctly. Look along the top and sides for debris, fabric, or objects that could interfere with the seals.

Retract the awning and verify that both arms are locked in their travel positions. Secure window awnings, slide toppers, exterior televisions, antennas, and satellite equipment as applicable.

Retract the entry steps. Raise stabilizers, leveling jacks, tongue jacks, and fifth-wheel landing gear according to the manufacturer’s instructions.

Do not rely only on a dashboard light or control-panel indicator. Visually confirm that each component is in its proper travel position.

4. Inspect RV Tires and Wheels

Check tire pressure when the tires are cold, before travel has heated them. Use the inflation guidance provided for the specific tow vehicle, RV, tire, and load—not a guessed pressure or a number copied from another owner’s setup.

NHTSA recommends checking all tires, including spares, and using the vehicle information label or manufacturer’s instructions to determine the appropriate pressure. The pressure molded onto a tire’s sidewall is not automatically the correct operating pressure for every vehicle and load. Review the agency’s current tire safety guidance.

Inspect each tire for:

  • Cuts, bulges, cracks, or exposed material
  • Objects embedded in the tread
  • Unusual or uneven wear
  • Low pressure
  • Damage around the valve stem
  • Contact with the RV body, suspension, or another tire
  • Signs of excessive age or deterioration

Look behind and between the tires when possible. Confirm that valve extensions and tire-pressure sensors are secure.

Check wheel fasteners according to the RV, axle, and wheel manufacturers’ procedures. If a torque check is required, use the specified torque value and the correct tightening pattern. Do not treat “as tight as possible” as a substitute for the manufacturer’s specification.

WTT Tip: Tire pressure can change with temperature and elevation. Check it while the tires are cold and recheck when conditions change significantly.

For a deeper explanation of cold pressure, vehicle and RV placards, tire sidewall ratings and towing loads, see RV Tire Pressure When Towing: What PSI Should You Use?

5. Check the Hitch Connection

The exact hitch inspection depends on whether you are towing a travel trailer or a fifth wheel.

For a conventional travel trailer, confirm that:

  • The coupler is completely seated on the correct hitch ball.
  • The coupler latch is closed and secured.
  • The hitch pin and retaining clip are installed.
  • The weight-distribution components are installed as directed.
  • Sway-control equipment is connected correctly.
  • The tongue jack is fully raised.
  • Nothing is contacting the ground or tow vehicle.

For a fifth wheel, visually confirm that the hitch jaws are correctly positioned around the kingpin. Check the hitch indicator, locking handle, safety pin, electrical cable, and breakaway cable.

Complete the manufacturer’s prescribed connection test before raising the landing gear fully. Do not substitute a generic online procedure for the instructions supplied with the particular hitch.

If anything about the connection looks different from normal, stop and determine why before towing.

Final RV walk-around before leaving an American campground

6. Connect the Safety Chains and Breakaway Cable

Attach the safety chains or cables to the designated points on the tow vehicle. They should have enough movement for turns without dragging on the pavement.

Many conventional trailer instructions call for crossing the chains under the trailer tongue. Follow the hitch, trailer, and tow-vehicle manuals, along with the laws that apply to the states where you will travel.

Connect the breakaway cable according to its manufacturer’s instructions. It must be routed so it can activate the trailer’s breakaway system if the trailer separates without pulling during an ordinary turn.

Do not allow the breakaway cable to drag, wrap around moving hitch components, or interfere with the safety chains.

Confirm that the trailer’s breakaway battery is charged and maintained as required. If you do not know how to test the system safely, have a qualified RV technician demonstrate the correct procedure.

7. Inspect the Electrical Connection and Trailer Brakes

Insert the trailer’s electrical plug completely and secure the cable so it cannot drag or become pinched during a turn.

With another person watching from outside, test:

  • Left turn signal
  • Right turn signal
  • Brake lights
  • Tail and marker lights
  • Hazard lights
  • Reverse lights, if equipped

A failed electrical connection can affect both the trailer lights and electric brakes.

Confirm that the tow vehicle recognizes the trailer when applicable. Check the brake controller for warnings and complete the low-speed brake test described in its manual.

Brake-controller gain is not one universal number. Trailer weight, brake type, road conditions, controller design, and manufacturer instructions all matter. Adjust and test the controller using the approved procedure for your equipment.

8. Check the Propane System and Exterior Compartments

Inspect propane cylinders or the permanently mounted tank for secure attachment. Look for visible damage, loose mounting hardware, damaged hoses, or anything that appears different from its normal condition.

Follow the RV and appliance manufacturers’ instructions for traveling with propane appliances and cylinder valves. Propane restrictions can apply on certain ferries, tunnels, bridges, and other routes.

Never use a flame to search for a propane leak. If you smell propane, avoid creating sparks or operating electrical switches. Move away from the RV and contact a qualified professional or emergency service as appropriate.

Close and latch every exterior storage compartment. Secure batteries, generators, fuel containers, bicycles, grills, ladders, and other equipment carried outside the living area.

9. Verify Cargo and Weight Limits

A visual inspection cannot prove that an RV is within its weight limits. The most dependable method is to weigh the loaded combination and compare the results with the applicable ratings.

Review:

  • Gross Vehicle Weight Rating
  • Gross Axle Weight Ratings
  • Gross Combined Weight Rating
  • Tire load limits
  • Receiver and hitch ratings
  • Tongue-weight or pin-weight limits
  • Cargo-carrying capacity

Passengers, pets, tools, fuel, water, batteries, hitch equipment, aftermarket accessories, and cargo all contribute to the load.

Remember that part of a trailer’s weight is transferred to the tow vehicle. That load reduces the tow vehicle’s remaining capacity for passengers and cargo.

If a weight exceeds a rating, remove or redistribute cargo as appropriate. Adding stronger suspension components does not automatically increase the ratings assigned by the vehicle manufacturer.

If these ratings are unfamiliar, read RV Weight Ratings Explained: GVWR, GCWR, Payload & Tongue Weight for a complete explanation of how the numbers work together.

10. Inspect the Tow Vehicle or Motorhome

Check the tow vehicle or motorhome using its owner’s manual and normal pre-drive procedure.

Inspect:

  • Engine oil and other required fluids
  • Fuel and diesel exhaust fluid, if applicable
  • Tire pressure and visible tire condition
  • Mirrors and towing cameras
  • Headlights, signals, and brake lights
  • Windshield, wipers, and washer fluid
  • Dashboard warnings
  • Battery condition
  • Tow/haul or trailer mode
  • Emergency equipment

Adjust the mirrors so the driver can monitor the sides of the RV and surrounding traffic. Clean cameras and lights if dirt or road spray limits visibility.

Do not begin towing with an unexplained warning light, active leak, unusual tire condition, or known brake problem.

11. Complete the Final Walk-Around

Walk around the rig in the same direction every time. Start at the driver’s door, move around the entire combination, and return to the starting point.

Look high enough to see awnings, antennas, roof vents, and tree clearance. Look low enough to see jacks, steps, hoses, cords, chocks, leaks, and hanging components.

During the final walk-around, confirm:

  • All people and pets are safely positioned.
  • Campsite hookups are disconnected.
  • Doors, windows, and compartments are secured.
  • Slides, awnings, steps, and jacks are retracted.
  • Tires appear properly inflated and undamaged.
  • Hitch components are connected.
  • Safety chains and breakaway cable are attached.
  • Electrical cable is secure.
  • Lights and trailer brakes work.
  • The departure path is clear.
  • Nothing remains on the roof, bumper, ground, or picnic table.

Remove the wheel chocks only when the RV is connected, secured, and ready to move under the procedure required for your setup.

WTT Tip: Before pulling out, pause at the driver’s door and ask, “Is the RV ready to move?” That brief pause can prevent an automatic departure before the final check is complete.

Final RV walk-around before leaving an American campground

What to Check Immediately After Pulling Away

Move slowly and listen for scraping, dragging, rattling, or another unfamiliar sound. Test the brakes at low speed using the procedure provided by the tow-vehicle and brake-controller manufacturers.

When it is safe, stop after leaving the site and inspect the rig again. This second check can catch a compartment that did not latch, a hitch component that shifted, or equipment that was difficult to see at the campsite.

Recheck items such as wheel fasteners and hitch equipment at the intervals specified by their manufacturers. Do not perform roadside checks where you or the RV would be exposed to traffic.


Towable RV and Motorhome Inspections Are Different

Travel trailers and fifth wheels require detailed attention to the connection between the RV and tow vehicle. This includes the hitch, safety equipment, wiring, brake controller, and weight distribution.

A motorhome does not have that primary hitch connection unless it is towing a vehicle or trailer. Its pre-trip inspection should instead include the chassis, engine compartment, fluid levels, air or hydraulic systems as equipped, dashboard warnings, mirrors, and any towed-vehicle equipment.

Motorhome owners towing a car should complete a separate inspection of the tow bar, baseplate, safety cables, supplemental braking system, breakaway device, lighting, and the towed vehicle’s required travel settings.

Always use the procedures provided by the motorhome, chassis, tow-bar, braking-system, and vehicle manufacturers.


Do You Need to Inspect the RV at Every Stop?

You do not need to repeat every interior step at every fuel or rest stop, but a brief exterior inspection is worthwhile.

Walk around the RV and look at the tires, wheels, hitch, safety equipment, electrical cable, doors, compartments, steps, awning, and anything carried outside. Check for unusual heat, odor, movement, leaks, or visible damage without touching components that may be hot.

A quick inspection is especially important after:

  • Rough roads or construction
  • Striking a pothole or road debris
  • Sudden braking
  • High winds
  • A noticeable change in handling
  • A warning from the tire-pressure monitoring system
  • Adjusting cargo or hitch equipment

If the trailer begins to feel unstable, slow down safely and stop somewhere protected from traffic. Do not continue until you determine what changed.

If the trailer feels different from normal, Why Does My Travel Trailer Feel Unstable? Common Causes and Fixes walks through weight distribution, tongue weight, tires, hitch setup, wind and other common causes of poor towing behavior.


Common RV Pre-Trip Inspection Mistakes

Rushing because checkout time is approaching

Begin packing early enough to complete the final inspection without pressure. A late departure is preferable to moving with a connected power cord, lowered jack, or unsecured hitch.

Dividing the inspection without communicating

Two people can complete the process faster, but each person may assume the other checked an important item. Assign specific areas and complete one final walk-around together.

Relying entirely on dashboard indicators

Sensors and warning lights are helpful, but they do not replace visual confirmation. A slide indicator cannot show a tree branch on the roof, and a trailer-connection message cannot confirm that the safety chains are attached correctly.

Checking tire pressure after driving

Driving warms the tires and changes the reading. Complete the primary pressure check when the tires are cold.

Tightening wheel fasteners without a specification

Improper torque can damage wheels, studs, or fasteners. Use the correct equipment and the manufacturer’s stated value and sequence.

Assuming yesterday’s setup is still correct

Equipment can loosen, cargo can shift, and road conditions can cause damage. Begin each towing day with a new inspection.

Using another RVer’s settings

Tire pressure, brake-controller gain, hitch adjustment, and cargo placement depend on the specific equipment and loaded combination. Use your ratings, weights, and manuals.


RV Pre-Trip Tools Worth Carrying

A small inspection kit can make the routine easier. Useful items may include:

  • Accurate tire-pressure gauge
  • Manufacturer-approved air compressor
  • Calibrated torque wrench and correct socket
  • Flashlight or headlamp
  • Work gloves
  • Tire tread-depth gauge
  • Basic hand tools
  • Wheel chocks
  • Reflective safety vest
  • Emergency warning triangles
  • Printed inspection checklist
  • Tire-pressure monitoring system, if appropriate for the RV

These tools do not replace proper training. Learn how to use each item before relying on it during a roadside problem.


Keep Your RV Checklists in One Place

The WTT RV Camping Companion keeps your arrival, setup, hookup, departure, and campground reminders together in one printable quick-reference system—giving you a repeatable routine to use from one RV trip to the next.


Organize the Entire Travel Day Before You Tow

A pre-trip inspection is only one part of a safe departure. You also need a suitable route, realistic driving schedule, fuel plan, weather check, campground information, and backup options.

RV LIFE Trip Wizard can help organize an RV route using the dimensions entered for the rig. It can also place fuel stops and campgrounds within the overall travel plan. Routing software does not replace checking current road conditions, posted signs, or your equipment.

The RV Travel Planning System provides space to organize travel days, fuel stops, campgrounds, packing, route information, and RV setup details in one place.


Frequently Asked Questions

How long should an RV pre-trip inspection take?

The time depends on the RV and how much equipment was used at the campsite. Once you establish a routine, the final inspection may take only several minutes, but disconnecting, packing, and testing systems will take longer.

Allow enough time to complete every step without rushing.

Should I inspect my RV before every travel day?

Yes. Complete a pre-trip inspection before moving the RV at the beginning of each travel day, even if the RV was inspected the previous evening.

Conditions can change overnight, and important items may have been used after the earlier inspection.

Should RV tire pressure be checked cold?

Yes. Check the primary tire pressure before travel heats the tires. Use the pressure guidance for your particular RV, tow vehicle, tires, and load.

Do not release air from a properly inflated hot tire merely to return it to the cold-pressure number.

Do I need to check trailer lug nuts before every trip?

Follow the wheel, axle, and RV manufacturers’ schedules. Checks may be required more frequently after wheel removal, new-wheel installation, or during an initial break-in period.

Use a calibrated torque wrench and the stated specification. Do not guess or simply tighten each fastener further.

How do I know whether my trailer brakes are working?

Check for brake-controller warnings and complete the manufacturer’s prescribed low-speed test in a safe location. The controller should activate the trailer brakes smoothly without causing them to lock.

If the trailer does not respond normally, do not enter highway traffic until the system has been inspected.

Should the propane be turned off while towing?

Follow the RV and appliance manufacturers’ instructions along with the rules for the route you will travel. Restrictions may apply in tunnels, on ferries, at fuel stations, or in other locations.

If you are uncertain, turn off the appliances and cylinder or tank valves according to their instructions before departure.

Who should complete the final walk-around?

One person should take responsibility for the final complete walk-around, even if several people helped pack and disconnect the RV.

The driver should know that the inspection was completed before moving the rig.

Does this checklist replace an annual RV inspection?

No. A pre-trip checklist identifies visible or functional concerns before departure. It does not replace scheduled inspection and service of brakes, bearings, tires, suspension, propane equipment, electrical systems, appliances, roof components, or the tow vehicle.


Bottom Line

A good RV pre-trip inspection follows the same sequence every time: secure the interior, disconnect campsite equipment, retract exterior components, check tires and wheels, verify the hitch and safety connections, test the lights and brakes, and finish with a complete walk-around.

Do not rush through a problem or rely only on an indicator light. If something looks, sounds, or feels different, stop and investigate before entering traffic.

A few extra minutes at the campsite can prevent damaged equipment, roadside delays, and unsafe towing conditions.


Plan Your RV Trip

Continue planning with these WTT guides:

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top